I’m in!

Within two days of receiving my eero device, I’ve got serial console root login!  I’ll detail how I did it in future posts.

U-Boot 2012.07 [standard IPQ806X.LN,r37758] (Apr 08 2016 - 19:01:11) 1.1.0

smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
NAND: SF: Detected N25Q064A with page size 64 KiB, total 8 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x800000
8 MiB
MMC: ipq_mmc: 0
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
cdp: get part failed for 0:HLOS
cdp: get part failed for rootfs
Net: athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
eth0, eth1
(Re)start USB...
USB0: Register 2000240 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000240 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
 scanning usb for storage devices... 0 Storage Device(s) found

** Invalid boot device **
Hit any key to stop autoboot: 9  0 
(eero) # <INTERRUPT>
(eero) # <INTERRUPT>
(eero) # <INTERRUPT>
(eero) # <INTERRUPT>
(eero) # printenv
baudrate=115200
bootarg_offset=44000000
bootargs=root=/dev/mmcblk0p3 loglevel=7 rdinit=/bin/kinit rw single console=ttyMSM0,115200n8 earlyprintk
bootcmd=ext2load mmc 0:1 0x44000000 eero_kernel.itb && bootm; reset
bootdelay=9
eth1addr=[redacted]
ethact=eth0
ethaddr=[redacted]
fdt_high=0xffffffff
ipaddr=192.168.2.101
machid=12ce
ramdisk_offset=44000000
stderr=serial
stdin=serial
stdout=serial
ver=U-Boot 2012.07 [standard IPQ806X.LN,r37758] (Apr 08 2016 - 19:01:11) 1.1.0

Environment size: 520/65531 bytes
(eero) # reset
resetting ...

Resetting with watch dog!



U-Boot 2012.07 [standard IPQ806X.LN,r37758] (Apr 08 2016 - 19:01:11) 1.1.0

smem ram ptable found: ver: 0 len: 5
DRAM: 491 MiB
NAND: SF: Detected N25Q064A with page size 64 KiB, total 8 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x800000
8 MiB
MMC: ipq_mmc: 0
PCI0 Link Intialized
PCI1 Link Intialized
In: serial
Out: serial
Err: serial
cdp: get part failed for 0:HLOS
cdp: get part failed for rootfs
Net: athrs17_reg_init: complete
athrs17_vlan_config ...done
S17c init done
eth0, eth1
(Re)start USB...
USB0: Register 2000240 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
USB1: Register 2000240 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
 scanning usb for storage devices... 0 Storage Device(s) found

** Invalid boot device **
Hit any key to stop autoboot: 9  8  7  6  5  4  3  2  1  0 
Loading file "eero_kernel.itb" from mmc device 0:1 (kernel0)
6387320 bytes read
## Booting kernel from FIT Image at 44000000 ...
 Using 'config@1' configuration
 Trying 'kernel@1' kernel subimage
 Description: ARM OpenWrt Linux-3.14
 Type: Kernel Image
 Compression: gzip compressed
 Data Start: 0x440000e0
 Data Size: 6358649 Bytes = 6.1 MiB
 Architecture: ARM
 OS: Linux
 Load Address: 0x42208000
 Entry Point: 0x42208000
 Hash algo: crc32
 Hash value: e7ae46ce
 Hash algo: sha1
 Hash value: ea1e3c6c76154f6e8212647e82aefb2d9d54de7f
 Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 44000000
 Using 'config@1' configuration
 Trying 'fdt@1' FDT blob subimage
 Description: ARM OpenWrt qcom-ipq8062-ap145 device tree blob
 Type: Flat Device Tree
 Compression: uncompressed
 Data Start: 0x44610898
 Data Size: 27323 Bytes = 26.7 KiB
 Architecture: ARM
 Hash algo: crc32
 Hash value: 52066729
 Hash algo: sha1
 Hash value: 70d930c22aafc2a44a1f8955cd1477a07240769f
 Verifying Hash Integrity ... crc32+ sha1+ OK
 Booting using the fdt blob at 0x44610898
 Uncompressing Kernel Image ... OK
 Using Device Tree in place at 44610898, end 4461a352
Using machid 0x12ce from environment

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0 (root@build) (gcc version 4.7.3 (Ubuntu/Linaro 4.7.3-12ubuntu1) ) #5 SMP PREEMPT Fri Apr 29 01:05:37 UTC 2016
[ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Ignoring memory below PHYS_OFFSET: 0x40000000-0x42000000
[ 0.000000] Machine model: Qualcomm IPQ8062/AP145
[ 0.000000] cma: CMA: reserved 8 MiB at 5f800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 7 pages/cpu @9d419000 s8064 r8192 d12416 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920
[ 0.000000] Kernel command line: root=/dev/mmcblk0p3 loglevel=7 rdinit=/bin/kinit rw single console=ttyMSM0,115200n8 earlyprintk
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 466852K/491520K available (7346K kernel code, 331K rwdata, 1888K rodata, 1655K init, 814K bss, 24668K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0x9e800000 - 0xff000000 (1544 MB)
[ 0.000000] lowmem : 0x80000000 - 0x9e000000 ( 480 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80208000 - 0x80b0cc78 (9236 kB)
[ 0.000000] .init : 0x80b0d000 - 0x80caaf80 (1656 kB)
[ 0.000000] .data : 0x80cac000 - 0x80cfec38 ( 332 kB)
[ 0.000000] .bss : 0x80cfec38 - 0x80dca7dc ( 815 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Offload RCU callbacks from all CPUs
[ 0.000000] Offload RCU callbacks from CPUs: 0-1.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000012] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 687194767200ns
[ 0.000289] Console: colour dummy device 80x30
[ 0.000899] Calibrating delay loop... 818.38 BogoMIPS (lpj=4091904)
[ 0.041426] pid_max: default: 32768 minimum: 301
[ 0.041569] Security Framework initialized
[ 0.041613] AppArmor: AppArmor disabled by boot time parameter
[ 0.041689] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.041704] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.049153] CPU: Testing write buffer coherency: ok
[ 0.049435] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.049505] Setting up static identity map for 0x4221a080 - 0x4221a0b4
[ 0.125318] CPU1: Booted secondary processor
[ 0.186144] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.186285] Brought up 2 CPUs
[ 0.186304] SMP: Total of 2 processors activated (1231.25 BogoMIPS).
[ 0.186313] CPU: All CPU(s) started in SVC mode.
[ 0.187141] devtmpfs: initialized
[ 0.205896] VFP support v0.3: implementor 51 architecture 0 part 4d variant 2 rev 0
[ 0.206496] pinctrl core: initialized pinctrl subsystem
[ 0.207341] regulator-dummy: no parameters
[ 0.211759] NET: Registered protocol family 16
[ 0.217443] DMA: preallocated 6144 KiB pool for atomic coherent allocations
[ 0.218616] cpuidle: using governor ladder
[ 0.243224] scm_call failed with error code -4
[ 0.243254] read_version: Error in QFPROM read (-95, 0)
[ 0.243272] 
[ 0.243272] Version Read Failed with error -95
[ 0.246772] ipq8064-pinctrl 800000.pinmux: Invalid config param 000a
[ 0.246794] ipq8064-pinctrl 800000.pinmux: pin_config_group_set op failed for group 1
[ 0.246816] ipq8064-pinctrl 800000.pinmux: Error applying setting, reverse things back
[ 0.246843] ipq8064-pinctrl 800000.pinmux: failed to select default state
[ 0.250894] qcom_rpm 108000.rpm: RPM firmware 1.0.133
[ 0.266888] bio: create slab <bio-0> at 0
[ 0.320625] qcom_pcie 1b500000.pci: link initialized 0
[ 0.320881] qcom_pcie 1b500000.pci: PCI host bridge to bus 0000:00
[ 0.320904] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff]
[ 0.320917] pci_bus 0000:00: root bus resource [io 0xfe00000-0xfefffff]
[ 0.320932] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.321662] PCI: bus0: Fast back to back transfers disabled
[ 0.321683] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.322833] PCI: bus1: Fast back to back transfers disabled
[ 0.323007] pci 0000:00:00.0: BAR 14: assigned [mem 0x08000000-0x081fffff]
[ 0.323025] pci 0000:00:00.0: BAR 15: assigned [mem 0x08200000-0x082fffff pref]
[ 0.323047] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit]
[ 0.323106] pci 0000:01:00.0: BAR 6: assigned [mem 0x08200000-0x0820ffff pref]
[ 0.323122] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.323149] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff]
[ 0.323174] pci 0000:00:00.0: bridge window [mem 0x08200000-0x082fffff pref]
[ 0.382669] qcom_pcie 1b700000.pci: link initialized 0
[ 0.382901] qcom_pcie 1b700000.pci: PCI host bridge to bus 0001:00
[ 0.382917] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff]
[ 0.382931] pci_bus 0001:00: root bus resource [io 0x31e00000-0x31efffff]
[ 0.382945] pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.383610] PCI: bus0: Fast back to back transfers disabled
[ 0.383628] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.384765] PCI: bus1: Fast back to back transfers disabled
[ 0.384932] pci 0001:00:00.0: BAR 14: assigned [mem 0x2e000000-0x2e1fffff]
[ 0.384949] pci 0001:00:00.0: BAR 15: assigned [mem 0x2e200000-0x2e2fffff pref]
[ 0.384968] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit]
[ 0.385023] pci 0001:01:00.0: BAR 6: assigned [mem 0x2e200000-0x2e20ffff pref]
[ 0.385038] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 0.385064] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff]
[ 0.385085] pci 0001:00:00.0: bridge window [mem 0x2e200000-0x2e2fffff pref]
[ 0.385871] SDCC Power: 3300 mV 
[ 0.386192] SDCC I/O Power: 1800 mV 
[ 0.386238] SDCC I/O Power: Failed to create debugfs directory
[ 0.386474] Core Power: 1150 mV 
[ 0.387964] vgaarb: loaded
[ 0.388606] SCSI subsystem initialized
[ 0.389274] usbcore: registered new interface driver usbfs
[ 0.389372] usbcore: registered new interface driver hub
[ 0.389564] usbcore: registered new device driver usb
[ 0.393988] i2c-gpio i2c.12: using pins 57 (SDA) and 58 (SCL)
[ 0.394385] msm_bus_fabric_init_driver
[ 0.395959] pcie_init: pcie_init: unable to create IPC log context for pcie0-short
[ 0.395974] pcie_init: pcie_init: unable to create IPC log context for pcie0-long
[ 0.395984] pcie_init: pcie_init: unable to create IPC log context for pcie1-short
[ 0.395993] pcie_init: pcie_init: unable to create IPC log context for pcie1-long
[ 0.396473] Switched to clocksource dg_timer
[ 0.396876] FS-Cache: Loaded
[ 0.397156] CacheFiles: Loaded
[ 0.413000] NET: Registered protocol family 2
[ 0.413929] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.413969] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.414026] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.414068] TCP: reno registered
[ 0.414091] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.414113] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.414395] NET: Registered protocol family 1
[ 0.674978] msm_rpm_log_probe: OK
[ 0.676940] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.677030] audit: initializing netlink subsys (disabled)
[ 0.677138] audit: type=2000 audit(0.660:1): initialized
[ 0.686939] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.687210] fuse init (API version 7.22)
[ 0.696449] NET: Registered protocol family 38
[ 0.697889] Crypto Speed tests
[ 0.697947] OCF: testing ...
[ 0.697961] crypto_newsession failed 22
[ 0.698050] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.698064] io scheduler noop registered
[ 0.698075] io scheduler deadline registered (default)
[ 0.698294] io scheduler cfq registered
[ 0.700551] crc32: CRC_LE_BITS = 32, CRC_BE BITS = 32
[ 0.700565] crc32: self tests passed, processed 225944 bytes in 1068160 nsec
[ 0.701631] crc32c: CRC_LE_BITS = 32
[ 0.701642] crc32c: self tests passed, processed 225944 bytes in 522880 nsec
[ 1.191579] crc32_combine: 8373 self tests passed
[ 1.682172] crc32c_combine: 8373 self tests passed
[ 1.683588] PCI: enabling device 0000:00:00.0 (0140 -> 0143)
[ 1.684091] PCI: enabling device 0001:00:00.0 (0140 -> 0143)
[ 1.685051] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[ 1.685067] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 1.685184] pcieport 0001:00:00.0: Signaling PME through PCIe PME interrupt
[ 1.685200] pci 0001:01:00.0: Signaling PME through PCIe PME interrupt
[ 1.688016] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0
[ 1.688543] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0
[ 1.689248] tcsr 1a400000.tcsr: setting usb port select = 3
[ 1.782484] msm_serial 16340000.serial: msm_serial: detected port #0
[ 1.782609] msm_serial 16340000.serial: uartclk = 1843200
[ 1.782680] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 184, base_baud = 115200) is a MSM
[ 1.783251] msm_serial: console setup on port #0
[ 2.650998] console [ttyMSM0] enabled
[ 2.655890] msm_serial: driver initialized
[ 2.659553] msm_serial_hs module loaded
[ 2.663076] qca_serial_hs_init: error creating logging context
[ 2.668204] 
[ 2.668204] Loaded Module Successfully!
[ 2.674855] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[ 2.679605] m25p80 spi32766.0: n25q064a (8192 Kbytes)
[ 2.685302] 7 ofpart partitions found on MTD device spi32766.0
[ 2.690335] Creating 7 MTD partitions on "spi32766.0":
[ 2.695989] 0x000000000000-0x000000220000 : "bootstrap"
[ 2.706344] ftl_cs: FTL header not found.
[ 2.706388] 0x000000220000-0x0000002a0000 : "u-boot"
[ 2.713360] ftl_cs: FTL header not found.
[ 2.715433] 0x0000002a0000-0x0000002e0000 : "u-boot env"
[ 2.721187] ftl_cs: FTL header not found.
[ 2.724719] 0x0000002e0000-0x000000320000 : "art"
[ 2.730412] ftl_cs: FTL header not found.
[ 2.733313] 0x000000320000-0x000000330000 : "identity"
[ 2.738291] ftl_cs: FTL header not found.
[ 2.742343] 0x000000330000-0x000000340000 : "secret"
[ 2.747398] ftl_cs: FTL header not found.
[ 2.751455] 0x000000340000-0x000000800000 : "scratch"
[ 2.760524] ftl_cs: FTL header not found.
[ 2.760743] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 2.775518] libphy: Fixed MDIO Bus: probed
[ 2.776206] libphy: GPIO Bitbanged MDIO: probed
[ 2.820125] switch0: Atheros AR8337 rev. 2 switch registered on gpio-0
[ 4.778272] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 4.779249] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 4.784744] edma module_init
[ 4.794079] PPP generic driver version 2.4.2
[ 4.797071] PPP MPPE Compression module registered
[ 4.800800] NET: Registered protocol family 24
[ 4.805436] PPTP driver version 0.8.5
[ 4.810872] usb30.5 supply gdsc not found, using dummy regulator
[ 4.814527] dwc3 11000000.dwc3: no usb2 phy configured
[ 4.819742] platform 11000000.dwc3: Driver dwc3 requests probe deferral
[ 4.824746] usb30.6 supply gdsc not found, using dummy regulator
[ 4.831965] dwc3 10000000.dwc3: no usb2 phy configured
[ 4.837448] platform 10000000.dwc3: Driver dwc3 requests probe deferral
[ 4.842869] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.848912] ehci-pci: EHCI PCI platform driver
[ 4.855546] ehci-platform: EHCI generic platform driver
[ 4.861308] 100f8800.phy supply vddcx not found, using dummy regulator
[ 4.865112] 100f8800.phy supply v3p3 not found, using dummy regulator
[ 4.871797] 100f8800.phy supply v1p8 not found, using dummy regulator
[ 4.878282] 100f8800.phy supply vbus not found, using dummy regulator
[ 4.884823] 110f8800.phy supply vddcx not found, using dummy regulator
[ 4.891140] 110f8800.phy supply v3p3 not found, using dummy regulator
[ 4.897540] 110f8800.phy supply v1p8 not found, using dummy regulator
[ 4.903975] 110f8800.phy supply vbus not found, using dummy regulator
[ 4.911009] 100f8830.phy supply vddcx not found, using dummy regulator
[ 4.916898] 100f8830.phy supply v1p8 not found, using dummy regulator
[ 4.923288] qcom-dwc3-ssphy 100f8830.phy: cannot get HSIO settings from device node, using default values
[ 4.929860] 110f8830.phy supply vddcx not found, using dummy regulator
[ 4.939380] 110f8830.phy supply v1p8 not found, using dummy regulator
[ 4.945714] qcom-dwc3-ssphy 110f8830.phy: cannot get HSIO settings from device node, using default values
[ 4.953760] mousedev: PS/2 mouse device common for all mice
[ 4.962757] input: gpio-keys.14 as /devices/soc.3/gpio-keys.14/input/input0
[ 4.968349] i2c /dev entries driver
[ 4.977376] tmp102 0-0048: initialized
[ 4.978927] tmp102 0-0049: initialized
[ 4.982727] tmp102 0-004a: initialized
[ 4.993171] GPIO_WDT: failed to register misc device
[ 4.993217] Error: Driver 'gpio-wdt' is already registered, aborting...
[ 4.998060] SPEED BIN: 0
[ 5.003540] ACPU PVS: 2
[ 5.006330] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 5.008681] deviceless supply vcore_regulator not found, using dummy regulator
[ 5.015686] platform cpufreq-krait.0: Driver cpufreq-krait requests probe deferral
[ 5.023580] ipq8064-pinctrl 800000.pinmux: invalid group "gpio12" for function "sdc1"
[ 5.031922] mmc0: SDCC Version: 0x06000018
[ 5.038222] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 136,0 (pio)
[ 5.043409] mmci-pl18x 12400000.sdcc: DMA channels RX dma0chan1, TX dma0chan2
[ 5.097128] sdhci: Secure Digital Host Controller Interface driver
[ 5.097162] sdhci: Copyright(c) Pierre Ossman
[ 5.102449] Synopsys Designware Multimedia Card Interface Driver
[ 5.107280] usbcore: registered new interface driver ushc
[ 5.112709] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.121849] deviceless supply vcore_regulator not found, using dummy regulator
[ 5.126270] L2 @ QSB rate. Forcing new rate.
[ 5.131018] L2 @ 384000 KHz
[ 5.135326] CPU0 @ 800000 KHz
[ 5.137794] CPU1 @ QSB rate. Forcing new rate.
[ 5.141034] CPU1 @ 384000 KHz
[ 5.141706] mmc0: BKOPS_EN bit is not set
[ 5.147584] mmc0: new high speed MMC card at address 0001
[ 5.152410] mmcblk0: mmc0:0001 MMC04G 3.57 GiB 
[ 5.153529] NET: Registered protocol family 26
[ 5.153551] GACT probability on
[ 5.153569] Mirror/redirect action on
[ 5.154689] netem: version 1.3
[ 5.154765] u32 classifier
[ 5.154771] Performance counters on
[ 5.154775] input device check on
[ 5.154779] Actions configured
[ 5.154815] Netfilter messages via NETLINK v0.30.
[ 5.154842] nfnl_acct: registering with nfnetlink.
[ 5.154944] nf_conntrack version 0.5.0 (7422 buckets, 29688 max)
[ 5.155869] ctnetlink v0.93: registering with nfnetlink.
[ 5.155902] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net>
[ 5.156192] ipip: IPv4 over IPv4 tunneling driver
[ 5.157385] gre: GRE over IPv4 demultiplexor driver
[ 5.157392] ip_gre: GRE over IPv4 tunneling driver
[ 5.159543] IPv4 over IPSec tunneling driver
[ 5.160622] TCP: bic registered
[ 5.160633] TCP: cubic registered
[ 5.160642] TCP: westwood registered
[ 5.160652] TCP: highspeed registered
[ 5.160658] TCP: hybla registered
[ 5.160665] TCP: htcp registered
[ 5.160672] TCP: vegas registered
[ 5.160679] TCP: veno registered
[ 5.160685] TCP: scalable registered
[ 5.160693] TCP: lp registered
[ 5.160700] TCP: yeah registered
[ 5.160707] TCP: illinois registered
[ 5.160713] Initializing XFRM netlink socket
[ 5.161823] NET: Registered protocol family 10
[ 5.164960] sit: IPv6 over IPv4 tunneling driver
[ 5.167626] ip6_gre: GRE over IPv6 tunneling driver
[ 5.168978] NET: Registered protocol family 17
[ 5.169049] NET: Registered protocol family 15
[ 5.169061] NET: Registered protocol family 5
[ 5.169245] l2tp_core: L2TP core driver, V2.0
[ 5.169284] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 5.169290] l2tp_netlink: L2TP netlink interface
[ 5.170209] sctp: Hash tables configured (established 16384 bind 16384)
[ 5.171071] openvswitch: Open vSwitch switching datapath
[ 5.171511] mpls_gso: MPLS GSO support
[ 5.197536] regulator-dummy: disabling
[ 5.336704] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for vddcx
[ 5.336852] mmcblk0boot0: mmc0:0001 MMC04G partition 1 2.00 MiB
[ 5.337013] mmcblk0boot1: mmc0:0001 MMC04G partition 2 2.00 MiB
[ 5.337167] mmcblk0rpmb: mmc0:0001 MMC04G partition 3 128 KiB
[ 5.345034] mmcblk0: p1 p2 p3 p4 p5
[ 5.348415] mmcblk0boot1: unknown partition table
[ 5.349828] mmcblk0boot0: unknown partition table
[ 5.372625] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for v3p3
[ 5.377290] qcom-dwc3-hsphy 110f8800.phy: cannot set voltage for v1p8
[ 5.383721] regulator-dummy: operation not allowed
[ 5.390221] regulator-dummy: operation not allowed
[ 5.397228] qcom-dwc3-ssphy 110f8830.phy: cannot set voltage for vddcx
[ 5.657433] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.657525] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 5.662721] xhci-hcd xhci-hcd.0.auto: irq 142, io mem 0x11000000
[ 5.669948] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.675631] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.682407] usb usb1: Product: xHCI Host Controller
[ 5.689496] usb usb1: Manufacturer: Linux 3.14.0 xhci-hcd
[ 5.694200] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 5.701169] hub 1-0:1.0: USB hub found
[ 5.704514] hub 1-0:1.0: 1 port detected
[ 5.709127] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.712366] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 5.718212] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 5.725195] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.732233] usb usb2: Product: xHCI Host Controller
[ 5.739324] usb usb2: Manufacturer: Linux 3.14.0 xhci-hcd
[ 5.744027] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 5.750880] hub 2-0:1.0: USB hub found
[ 5.754328] hub 2-0:1.0: 1 port detected
[ 5.759796] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for vddcx
[ 5.762174] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for v3p3
[ 5.768660] qcom-dwc3-hsphy 100f8800.phy: cannot set voltage for v1p8
[ 5.775013] regulator-dummy: operation not allowed
[ 5.781524] regulator-dummy: operation not allowed
[ 5.788536] qcom-dwc3-ssphy 100f8830.phy: cannot set voltage for vddcx
[ 6.047369] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 6.047449] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 6.052596] xhci-hcd xhci-hcd.1.auto: irq 237, io mem 0x10000000
[ 6.059810] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.065565] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.072383] usb usb3: Product: xHCI Host Controller
[ 6.079434] usb usb3: Manufacturer: Linux 3.14.0 xhci-hcd
[ 6.084136] usb usb3: SerialNumber: xhci-hcd.1.auto
[ 6.090646] hub 3-0:1.0: USB hub found
[ 6.094428] hub 3-0:1.0: 1 port detected
[ 6.098746] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 6.102286] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 6.107988] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 6.115123] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.122136] usb usb4: Product: xHCI Host Controller
[ 6.129256] usb usb4: Manufacturer: Linux 3.14.0 xhci-hcd
[ 6.133957] usb usb4: SerialNumber: xhci-hcd.1.auto
[ 6.140476] hub 4-0:1.0: USB hub found
[ 6.144240] hub 4-0:1.0: 1 port detected
[ 6.148845] SPEED BIN: 0
[ 6.152092] ACPU PVS: 2
[ 6.154639] deviceless supply vcore_regulator not found, using dummy regulator
[ 6.156881] regulator-dummy: Failed to create debugfs directory
[ 6.164364] Frequency table not initialized.
[ 6.170062] Frequency table not initialized.
[ 6.174445] Frequency table not initialized.
[ 6.178734] Frequency table not initialized.
[ 6.182910] Frequency table not initialized.
[ 6.187415] Frequency table not initialized.
[ 6.191472] Frequency table not initialized.
[ 6.195689] Frequency table not initialized.
[ 6.200057] Frequency table not initialized.
[ 6.204175] Frequency table not initialized.
[ 6.218326] Freeing unused kernel memory: 1652K (80b0d000 - 80caa000)
 argc == 8
 argv[0]: "/bin/kinit"
 argv[1]: "root=/dev/mmcblk0p3"
 argv[2]: "loglevel=7"
 argv[3]: "rdinit=/bin/kinit"
 argv[4]: "rw"
 argv[5]: "single"
 argv[6]: "console=ttyMSM0,115200n8"
 argv[7]: "earlyprintk"
Running ipconfig
 argc == 3
 argv[0]: "IP-Config"
 argv[1]: "-i"
 argv[2]: "Linux kinit"
IP-Config: no devices to configure
kinit: do_mounts
kinit: try_name mmcblk0,3 = mmcblk0p3(179,3)
kinit: name_to_dev_t(/dev/mmcblk0p3) = mmcblk0p3(179,3)
kinit: root_dev = mmcblk0p3(179,3)
kinit: mounting root rw
kinit: /dev/root appears to be a ext4 filesystem
kinit: trying to mount /dev/root on /root with type ext4, flags 0x8000, data '(null)'
[ 6.416902] usb 3-1: new full-speed USB device number 2 using xhci-hcd
[ 6.557631] usb 3-1: New USB device found, idVendor=0cf3, idProduct=3004
[ 6.557659] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 8.142518] EXT4-fs (mmcblk0p3): recovery complete
[ 8.144170] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
kinit: Mounted root (ext4 filesystem).
Checking for init: /sbin/init
Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory
[ 8.718645] random: init urandom read with 93 bits of entropy available
[ 9.200508] init: mounted-proc main process (282) terminated with status 1
Starting Hardware RNG entropy gatherer daemon: rngd.
net.core.rmem_default = 8388608
net.core.wmem_default = 8388608
net.core.rmem_max = 8388608
net.core.wmem_max = 8388608
net.ipv4.tcp_wmem = 1048576 2097152 8388608
net.ipv4.tcp_rmem = 1048576 2097152 8388608
net.core.netdev_max_backlog = 2000
net.ipv4.ip_forward = 1
autoneg unmodified, ignoring
autoneg unmodified, ignoring
dev.nss.general.jumbo_mru = 9000
dev.nss.general.redirect = 1
sysctl: setting key "dev.nss.general.rps": Invalid argument
dev.nss.general.rps = 1
e2fsck 1.42.9 (4-Feb-2014)
/dev/mmcblk0p5 was not cleanly unmounted, check forced.
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/mmcblk0p5: 27/7936 files (0.0% non-contiguous), 1414/31744 blocks
root@eero:~# [ 15.635527] AHB support is still work in progress
[ 18.103697] watchdog watchdog0: watchdog did not stop!
[ 27.653484] zorgo_0_0: Not creating an NSS virtual interface
[ 28.903518] zorgo_1_0: Not creating an NSS virtual interface

root@eero:~# 
root@eero:~#

Leave a Reply